Many friends' knowledge of x-ray machines is only in the aspect of security inspection. There is still a lot of information that everyone does not know. What are the operating procedures and precautions of X-ray machines? I believe that many of my friends want to know the true information, so let's take a brief introduction to you by Shenzhen Jin Ri'an.
X-ray machine operation process and precautions:
1. Please do not turn on the equipment that has not been used for more than 6 months. The X-ray generator must be restarted by professional technicians, otherwise the X-ray generator may be damaged.
2. Before operating the equipment, you should be aware of the applicable radiation protection regulations.
3. If someone else is going to operate your equipment, make sure that he is a qualified operator and understand all safety instructions, laws and regulations.
4. Installation, electrical connection and replacement of mechanical and electrical components can only be carried out by experienced professional technicians.
5. If the enclosure components, cables or belts of the equipment are damaged, the operation must be stopped immediately.
6. The outer casing and parts of the equipment can only be opened by qualified professional technicians.
7. It is forbidden to modify or change any part of the system safety. The installation, commissioning or maintenance of the equipment can only be completed by qualified personnel who have received training.
8, the equipment can only be used to check the items, it is strictly prohibited to check the human body or other living things.
9. It is forbidden to sit or stand on the conveyor belt.
10. It is forbidden to enter any part of the body into the inspection channel when starting the device.
11. Ensure that the baggage is not stacked in the detection channel or at the exit end. If the baggage is blocked by the inspection channel, it should be shut down first before cleaning up.
12. Prevent all kinds of liquid from flowing into the machine. If this happens, shut down immediately.
13. The vents on the device and display cannot be blocked.
14. The system must be grounded before work. The main power socket and installation site must have a reliable grounding configuration.
15. When the equipment is working, try to avoid standing near the exit and entrance of the passage.
16. When the lead curtain is damaged or opened, the equipment cannot be operated.
17. Although the X-ray dose is small, non-workers should try to stay away from the equipment.
The above information is that Shenzhen Jin Ri'an simply introduced the X-ray machine operation process and precautions for everyone. I believe that you should have some information on this aspect through the above information. If you want to know more about X-rays For other information on the machine, you can pay attention to Shenzhen Jin Ri'an to carry out detailed information and hope that the above information can help everyone.
Ridge Cap Roll Forming Machine
Ridge Cap Roll Forming Machine
Colored steel ridge cap forming machine is the machine to produce ridge caps for top part of roof, it is covered on the joint part of the two roofing sheet.
The Ridge cap tile will be used on the ridge of the roof or other place.
It can be used well with the glazed tile produced by roll forming machine.
It can be used well with the trapezoidal tile produced by roll forming machine.
Technique parameters
(1) Processing material: Aluminum/galvanized steel/colored steel coil
(2) Material thickness:0.3- 0.8mm
(3) Product size:5800*1500*1300mm
(4) Main motor power: 4kw
(5) Pump power:4kw
(6) Shaft diameter: 75mm
(7) Forming steps: 13 steps
(8) Roller material: high grade 45# steel, hard Chromium plating
(9) Main frame: 300H Steel
(10) Medium plate thickness: 16mm
(11) Speed:8-12m/min
(12)Material of the cutting blade: Cr 12 mould steel with quenched treatment
(13) Control system: PLC computer control
(14) Power supply: 380V, 3 Phase, 50Hz (can change as customers request)
Components of line
1.Decoiler 1 unit
2.Roll Forming System 1 unit
3.Cutting Device 1 unit
4.Hydraulic Station 1 unit
5.PLC control system 1 unit
Working Flow:
Loading coil – decoiling – guide feeding – main roll forming – hydrarlic cutting – finished products
